View and Download Polaris RANGER owner’s manual online. RANGER Offroad Vehicle pdf manual download. Also for: Ranger 6×6 , Ranger Related Manuals for Polaris Ranger RZR EFI. Utility Vehicle Polaris Ranger EV Owner’s Manual For Maintenance And Safety. (68 pages). View and Download Polaris Ranger HD owner’s manual online. Polaris Sales Utility Vehicle Polaris Ranger RZR EFI Manual. ( pages).

Author: Taukree Shaktigal
Country: Nigeria
Language: English (Spanish)
Genre: Business
Published (Last): 5 July 2012
Pages: 335
PDF File Size: 2.84 Mb
ePub File Size: 18.76 Mb
ISBN: 457-9-41114-824-4
Downloads: 24108
Price: Free* [*Free Regsitration Required]
Uploader: Tesida

This warranty does not cover accidental damage, normal wear and tear, abuse or improper handling. Spring Preload Adjustment The front and rear shocks have a preload adjustment. Do lwners reuse a ball joint if it has been removed for any reason. Allow it to idle for one to two minutes. Don’t show me this message again. Electrical circuits are off, except Acc, 12V. Install a new shift cable lever seal and press it flush with the case.

Grease the joint with the special joint grease provided in the Lubricate the shaft of the shifter assembly and install the assembly into the housing with a new retaining ring and washer.

Front wheel can be removed to gain better 40 Nm. Do not perform service on the spark arrestor while the system is hot.

Polaris 2010 Ranger RZR 800 EFI Manual

Mark or tag rocker arms in order of disassembly to keep them in order for reassembly. Set the selector dial to measure AC Voltage. Pry the shift lever cover using a suitable tool and remove the screw.


Transmission Transmission Fluid ml Do not touch the ownwrs or PC during the process. Engine speed is limited to RPM in all gears, except neutral.

See page 54 for operating instructions. Combustion Area Install pilot into valve guide. Use the strap adjusters to 20100 any loose straps. Remove the valve lifters by reaching into the crankcase and pushing the lifter up through the lifter bore by hand.

Carefully drive the ball joint into place until the ball joint Sway Bar Linkage Removal is properly seated. Gasoline is extremely flammable. Add brake fluid to the indicated MAX level of reservoir.

Clean lights frequently and replace burned out lamps promptly. Remove the front output pinion shaft ranyer. Remove Fasteners Inspect the stabilizer bar for straightness. Slide the joint onto the drive shaft splines and align the Securing a Net Latch 1. Maintain the fluid level even with the bottom of the fill plug hole.

Polaris recommends using a rigid hone or arbor If cylinder wear or damage is excessive, it will be necessary to honing machine. The correct position of the TPS angle on the throttle polris is established and set at the factory. RH Hub Clutch Housing Ring gear backlash is set from the factory. Polaris measures chain length in number of pitches.



Elevate the rear of the vehicle off the ground using a Line Up Marks Immersion can result in major damage if the vehicle isn’t serviced correctly and promptly.

Keep the reservoir as straight as possible to prevent the safety needle from bending. Page of Go. Before replacing the bulb suse a digital multi-meter to test the Remove the O-rings A from the headlamp brackets on harness to ensure the lamp is receiving 12 volts and that a ground both sides of the headlamp.

Piston should slide in and out of bore smoothly with light resistance. Page 21 Change shock oil and seals Inspect periodically; adjust when parts are Toe Adjustment replaced Headlight Aim Adjust as needed Perform these procedures more often for vehicles subjected to severe use. Steering 58 Nm 23 ft. Torque wheel nuts to Remove the two brake caliper attaching bolts.

Install a new input shaft seal using a standard seal mamual or other suitable method. While installing in piston circlips, cover all