CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

0

CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Voodoozahn Gardataur
Country: Italy
Language: English (Spanish)
Genre: Environment
Published (Last): 7 May 2017
Pages: 127
PDF File Size: 13.26 Mb
ePub File Size: 10.17 Mb
ISBN: 536-9-36158-111-8
Downloads: 59005
Price: Free* [*Free Regsitration Required]
Uploader: Dok

Additionally, if the switch is connected to other switches in the network, you can remove the VLANs but they might be relearned from another switch via VTP. Configure PortFast on an access port.

Authentication is configured by defining a list of methods for authentication and applying that list to specific interfaces.

You can use other 6. such as orswitches such asand Cisco IOS Software versions if they have comparable capabilities and features.

An amber light indicates an inactive link.

CCNP SWITCH Lab Manual, 2nd Edition

To achieve some load balancing, use the standby [group] priority swtch. Use the show vlan brief command to view the VLAN configurations. Inter-switch Connectivity Configuration Requirements. Optionally, configure an enable secret password and console security. The connected ports of the respective switches were configured using the swotch mode trunk command. In such a failure, loop guard puts it into loop-inconsistent state to block the whole channel.

  EL DIABLO EN EL INFIERNO DECAMERON PDF

You can use dashes, commas, or both, depending on the situation. Change the VLAN names.

Was the ping successful this time? After authentication succeeds, normal traffic can pass through the port. End, Status Passed Waiting for Port download Make sure to use the appropriate country code. The access layer switches act as Layer 2 devices and need a default gateway to send management VLAN traffic off of the local subnet. First, enable port security with the switchport port- security command.

Traffic between VLANs must be routed. This document is exclusive property of Cisco Systems, Inc. On each switch, erase the startup configuration, delete the vlan.

Background When working with a switch that has been previously configured, any new commands entered are merged with the existing configuration, causing unpredictable results.

It is not necessary to specify the maximum number of addresses, unless it is greater than 1. Use the show interfaces trunk command on DLS2. Which switch is the root bridge? Examine the CEF configuration.

Issue the show spanning-tree root command on ALS1. ALS1 show etherchannel summary Flags: Set up the VLANs according to the diagram. At lunch, he brings up the subject of network security and how two of his former co-workers had been arrested for using different Layer 2 attack techniques to gather data from other users in the office for their own personal gain in their careers and finances.

  BORG WARNER 4405 PDF

Ccnp Tshoot Lab Manual Configuration Files – downloadsoftspecialists

Verify that the configurations from Lab are loaded on the devices by issuing the show vtp status command. Below are the screenshots of the lab files. Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device.

However, the VLAN database insructor still accessible for those who choose to use it. Change the revision number by typing revision number. Your output may differ, based on the root bridge selected in your topology.

ccnp-switch-instructor-lab-manual-slm

This allows the link to the router to rapidly transition to the forwarding state despite being a trunk. The switches can use different methods to load-balance traffic going through a port channel. Configure an access list on DLS1 called temp-host using the ip access-list extended name command.

Optional Set an enable secret password and configure the vty lines for Telnet access to the switch. This is the result of the channel-group x mode being set to active. Remove all VLAN information and configurations that may have been previously entered into the switches.