and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.

Author: Feran Vogis
Country: Mozambique
Language: English (Spanish)
Genre: Spiritual
Published (Last): 7 September 2009
Pages: 241
PDF File Size: 3.27 Mb
ePub File Size: 5.20 Mb
ISBN: 596-5-47225-499-6
Downloads: 43849
Price: Free* [*Free Regsitration Required]
Uploader: Balkree

During this testing stage take extreme care not to touch any live or hazardous parts. B Optional equipment connector port. Check the output LEDs for operation.

The FX1N does hardwwre have battery backup, if a system requires backup of more than 10 days, a peripheral backup power source must be provided. Check the hardwrae down loaded program works correctly. See equation 1 for Rb calculation. Remove the base unit top cover. If a high speed response is required, a current of 10 – mA must be used.

These engineers should be fully aware of all aspects of safety with regards to automated equipment. These engineers should also be trained in the use and maintenance of the completed product. The rated life for an inductive AC load such as a contactor or solenoid valve isoperations at 20VA. Do not use this terminal Fuse Surge absorbing Diode. For greater detail, specifications and wiring examples for each optional unit, please see the relevant product manuals.

Hardwaree resistance Rp is less than the stated value, then add Rb.

Mitsubishi FX1NMT-DSS Manuals

This includes being completely familiar with all associated documentation for the said product. Please note that the over current induced by in-rush greatly reduces the relay contacts service hardwsre.


Whenever any of the following symbols are encountered, its associated note must be read and understood. All maintenance should be carried out in accordance with established safety practices. A standard input X0 to Manjal defined by the system parameters.

Features table 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Harvware cover Direct mounting holes 4. Verify the program to ensure it has been written to the PLC correctly.

D, D M Program execution error ref. Mechanical interlocks MUST be fitted to all safety critical circuits. However Additional extension blocks can be powered from the main unit power supply 4.

Mitsubishi FX1N-24MT-ESS/UL Manuals

D Top cover for board. When using a DC powered unit, the input circuit power supply should be used. Only one special function board can be used at any time. Software warning 4 Indicates special care must be taken when using this element of software. Screw terminals must be secured to prevent a loose connection from causing a malfunction. DC source transistor, CE registered. The enclosure should be selected and installed in accordance to the local and national hardwwre.

If in doubt at any stage of the installation of an FX1N Series Programmable Controller always consult a professional electrical engineer who is qualified and trained to the local and national standards which apply to the installation site. Circuit protector or fuse?

FX1N Hardware Manual_图文_百度文库

E C A Special function or optional equipment board. This manual is subject to change without notice. Ground resistance must be less than ? Remove base unit top cover. The value depends on the switch setting. Check D for program scan time, units 0. Always make sure the power is turned off, before installing a special function board.


Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application. AC Manaul ld spec. C M3 screw to secure top cover. Remotely from a personal computer or other programming peripheral. D, Rx1n M ref.

Units should not be installed in areas subject to the following conditions: D, D M Program circuit error ref. All layouts are diagrammatic and are only intended to aid the creation of wiring diagrams.

The operators should also be familiar with documentation which is connected with the actual operation of the completed equipment. This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX 1N Series Programmable Controllers. If during the installation of these product or associated products concern is felt, please contact a professional electrician who is trained to the local and national standards applicable to the installation site.

Take special care not to allow debris to fall inside the unit during installation e. E M3 screw to secure top cover.